PLIC

The Platform Interrupt Controller (PLIC) is the standardized device for receiving, routing, and completing external interrupts with configuration per-hart and per-privilege mode. Originally, the PLIC design is based on early SiFive designs which were then slightly refined and standardized and only supports basic interrupt enabling/disabling, prioritization and routing. As part of the RISC-V Advanced Interrupt Architecture (AIA), the original PLIC design is extended to support more types of interrupts, namely Message Signaled Interrupts (MSIs), which are important for technologies like PCI. The PLIC specification can be found at https://github.com/riscv/riscv-plic-spec while the APLIC specification is available at https://github.com/riscv/riscv-aia.

Original PLIC Design

The original PLIC design consist of a set of: interrupt source priorities, interrupt pending bits, per-context interrupt enable bits, and then per-context priority threshold & claim/complete regions. A context is the combination of a hart ID and a privilege mode, though the specific ordering of contexts is platform-specific and cannot be generalized between them. A small table below has been added for quick reference, but likely will not contain a formula for calculating the context for every platform. The memory layout for the PLIC is as follows (taken from the PLIC spec):

base + 0x000000: Reserved (interrupt source 0 does not exist)
base + 0x000004: Interrupt source 1 priority
base + 0x000008: Interrupt source 2 priority
...
base + 0x000FFC: Interrupt source 1023 priority
base + 0x001000: Interrupt Pending bit 0-31
base + 0x00107C: Interrupt Pending bit 992-1023
...
base + 0x002000: Enable bits for sources 0-31 on context 0
base + 0x002004: Enable bits for sources 32-63 on context 0
...
base + 0x00207C: Enable bits for sources 992-1023 on context 0
base + 0x002080: Enable bits for sources 0-31 on context 1
base + 0x002084: Enable bits for sources 32-63 on context 1
...
base + 0x0020FC: Enable bits for sources 992-1023 on context 1
base + 0x002100: Enable bits for sources 0-31 on context 2
base + 0x002104: Enable bits for sources 32-63 on context 2
...
base + 0x00217C: Enable bits for sources 992-1023 on context 2
...
base + 0x1F1F80: Enable bits for sources 0-31 on context 15871
base + 0x1F1F84: Enable bits for sources 32-63 on context 15871
base + 0x1F1FFC: Enable bits for sources 992-1023 on context 15871
...
base + 0x1FFFFC: Reserved
base + 0x200000: Priority threshold for context 0
base + 0x200004: Claim/complete for context 0
base + 0x200008: Reserved
...
base + 0x200FFC: Reserved
base + 0x201000: Priority threshold for context 1
base + 0x201004: Claim/complete for context 1
...
base + 0x3FFF000: Priority threshold for context 15871
base + 0x3FFF004: Claim/complete for context 15871
base + 0x3FFF008: Reserved
...
base + 0x3FFFFFC: Reserved

Or, more usefully:

#[repr(C)]
struct Plic {
    source_priorities: [u32; 1024],
    interrupt_pending: [u32; 32],
    _padding1: [u8; 3968],
    interrupt_enable: [[u32; 32]; 15872],
    _padding2: [u8; 57344],
    threshold_and_claim: [[u32; 1024]; 15872],
}

Each u32 inside of the source_priorities is a priority level from 0..=7 (on most platforms, see your platform specification for more complete information) of increasing priority level where priority 0 is considered "never interrupt" and will cause the interrupt to effectively be disabled, with the exception of interrupt #0, which does not exist and is reserved. interrupt_pending is a read-only bitmap of the pending status for priorities 1..=1024 (with the interrupt #0 bit hardwired to zero). Both interrupt_enable and threshold_and_claim work on the aforementioned contexts, and need to be indexed at a platform-specific index for a given hart and privilege mode combination. The interrupt_enable consists of another bitmap of interrupt sources (again with interrupt #0 for each context being hardwired to zero) which allow enabling and disabling specific interrupt sources at the context level, but also means that if you wish for a given interrupt to trigger across any hart, it will need to be enabled for each context for the privilege mode you are executing in. threshold_and_claim is made up of a threshold u32 value and a claim u32 value, with the rest of the u32s being reserved and should not be written to.

Hart & Privilege Context Mappings

Platform	M-mode Context	S-mode Context
QEMU virt	hart_id * 2	hart_id * 2 + 1
QEMU sifive_u†	Monitor hart: 0 Other harts: hart_id * 2 + 1	hart_id * 2

^†This platform contains a Monitor Hart which does not support S-mode and does not have the same extension availability as the general-purpose harts

Enabling and Disabling Interrupts

To enable or disable any given interrupt source, simply toggle the specific bit that corresponds to the interrupt source in the interrupt_enable for the context for which you wish to enable or disable the interrupt. Example Rust code:

unsafe fn enable_interrupt(plic: *mut Plic, context: usize, interrupt_source: usize) {
    // Sanity checks, neither values would be valid
    if context >= 15872 || interrupt_source >= 1024 {
        return;
    }
    
    // Calculate the bit-group index and the bit index for that bit-group
    let (u32_index, bit) = (interrupt_source / 32, interrupt_source % 32);
    
    // Calculate the address of the bit-group
    let bit_group_ptr = unsafe { core::ptr::addr_of_mut!((*plic).interrupt_enable[context][u32_index]) };
    
    // Read the current value
    let previous = unsafe { bit_group_ptr.read_volatile() };
    
    // Set the bit for the interrupt source
    let new = previous | (1 << bit);
    
    // Write the new value
    unsafe { bit_group_ptr.write_volatile(new) };
}

unsafe fn disable_interrupt(plic: *mut Plic, context: usize, interrupt_source: usize) {
    // Sanity checks, neither values would be valid
    if context >= 15872 || interrupt_source >= 1024 {
        return;
    }
    
    // Calculate the bit-group index and the bit index for that bit-group
    let (u32_index, bit) = (interrupt_source / 32, interrupt_source % 32);
    
    // Calculate the address of the bit-group
    let bit_group_ptr = unsafe { core::ptr::addr_of_mut!((*plic).interrupt_enable[context][u32_index]) };
    
    // Read the current value
    let previous = unsafe { bit_group_ptr.read_volatile() };
    
    // Set the bit for the interrupt source
    let new = previous & !(1 << bit);
    
    // Write the new value
    unsafe { bit_group_ptr.write_volatile(new) };
}